OLI NATURA® Care Set No. 4 for Cutting Boards

Testing and product properties

The boiled linseed oil included in the OLI NATURA® Care Set No. 4 is:

• tested for food contact in accordance with the German Food and Feed Code (LFGB)
• meets the requirements of DIN EN 71-3 - Safety of toys
• meets the requirements of DIN 53160 - Resistance to saliva and perspiration
• free from cobalt and oximes
• free from formaldehyde, aromatics, biocides, and preservatives

Using the OLI NATURA® Care Set No. 4: Initial treatment and subsequent care of cutting boards

1. Initial treatment of raw or sanded cutting boards

The wood must be clean, dry, professionally sanded and free of dust.

Shake the container well. Apply OLI NATURA® boiled linseed oil thinly and evenly using a pad or brush. For longitudinal grain, work in the direction of the grain. If the wood absorbs the oil more quickly in some areas, apply a little more oil there.

Allow to penetrate for 15–30 minutes. Then completely remove excess oil with the oil-absorbent cloth or absorbent kitchen paper. No shiny or sticky areas may remain.

Allow the board to dry freestanding in a well-ventilated area for 16–24 hours. Repeat the application depending on the type of wood and its absorbency until the wood is evenly saturated. Usually, two to three thin coats are required.

The surface is fully cured and suitable for food contact after approximately 21 days.

Please note: End grain absorbs significantly more oil than longitudinal grain. Therefore, several coats and a larger quantity of oil may be required.

2. Care treatment and refreshing of oiled cutting boards

Clean the cutting board thoroughly and allow it to dry completely. If necessary, smooth rough areas and minor signs of use with the sanding sponge. Then carefully remove all dust.

Shake the container well. Apply a small amount of OLI NATURA® boiled linseed oil to a white pad or lint-free cotton cloth and work it in sparingly and evenly using circular motions.

Allow to penetrate for 15–30 minutes. Then completely remove excess oil with the oil-absorbent cloth or absorbent kitchen paper. No shiny or sticky areas may remain.

Allow the board to dry freestanding in a well-ventilated area for at least 24 hours. Handle it gently during the first few days and avoid prolonged contact with water.

Safety information for oil-soaked cloths and pads

Oil-soaked rags, pads or sponges can self-ignite due to heat buildup. After use, soak them completely in water or dry them individually, spread out flat. Never leave them crumpled up and dispose of them only once they are completely dry.

How to properly clean and care for cutting boards with the OLI NATURA® Care Set No. 4

Good cutting board care doesn’t have to be complicated. A little water, careful drying, and fresh oil from time to time are enough to keep wooden cutting boards and kitchen utensils looking beautiful and protected for a long time. The key is to remove dirt promptly and re-oil the wood before it becomes dry, faded, or rough.

Cutting boards prefer quick and thorough care

After each use, clean the board with warm water, a soft sponge, and a little mild dish soap. Clean it especially thoroughly after contact with raw meat, poultry, fish, or eggs.

Briefly wipe both sides with a damp cloth, dry the board immediately, and then leave it to dry completely on its edge. This allows air to reach both sides and helps the wood retain its shape.

Please do not soak the board or put it in the dishwasher. Prolonged heat, large amounts of water, and harsh cleaners can cause the wood to swell and lead to cracks or warping.

When the wood gets thirsty again

If the wood looks dry, faded, or rough, or if water no longer reliably beads up, it is time to refresh it. How often the board should be re-oiled depends on how intensively it is used and cleaned.

Smooth, oil, and refresh

Clean the board thoroughly and leave it to dry completely. If necessary, smooth rough areas and light signs of wear with the sanding sponge, then carefully remove all dust.

Shake the OLI NATURA® boiled linseed oil well. Apply a small amount sparingly and evenly to the wood with a pad. After 15–30 minutes, completely remove excess oil with the oil-absorbing cloth. No shiny or sticky areas should remain.

Freshly treated wood needs some time to rest

Leave the board freestanding in a well-ventilated area to dry for at least 24 hours. It is then ready for use again. Please handle it gently during the first few days and avoid prolonged contact with water.

When treating raw or completely sanded wood for the first time, several thin coats are required. The surface will be fully cured after around 21 days.

Handle oil-soaked cloths safely

Boiled linseed oil cures by absorbing oxygen from the air. This generates heat, which can accumulate in crumpled cloths or pads.

After use, soak oil-soaked materials completely in water or lay them out individually and flat to dry outdoors. Dispose of them only once they are completely dry.

The product is not subject to labelling requirements. The mixture is not classified as hazardous within the meaning of Regulation (EC) No 1272/2008. It must not be labelled with GHS hazard pictograms or signal words and is not classified as dangerous goods.

Safety information:

 Oil-soaked cloths/pads can spontaneously ignite due to heat accumulation! Therefore, clean them immediately after use or store them under water. P102 Keep out of reach of children.