OLI NATURA® Scandic-Oil CLASSIC

• Giscode: Ö10+ for 1K application / Ö20+/DD for 2K application
• EU Decopaint compliant
• Emission-tested building product according to ABG; DIBt approval Z-157.10-217
• Baubook declared 
• DIN EN 71-3 Migration of certain elements
• DIN 53160-1 and -2: Resistance to saliva and perspiration
• DIN EN 12720: Resistance to cold liquids tested according to test program 1B in accordance with DIN 68861-1
• VOC and formaldehyde emissions tested according to the AgBB scheme, ISO 16000-3, -6 and -9, and DIN EN 16516
• French VOC emissions class A+
• Belgian VOC emission requirements met

How to apply OLI NATURA® Scandic-Oil CLASSIC

Preparation: The wood must be clean, dry, and absorbent. Completely remove old film-forming coatings. Sand the floor evenly with P120–150 and vacuum thoroughly. Wood moisture content: 8–12 %.

Tip: Apply a test coat to wood prepared in the same way. The surface initially appears darker when wet. Only assess the raw wood effect after it has dried completely.

Hardener addition: For floors subject to heavier wear, use OLI NATURA® H2O-Hardener . Shortly before use, thoroughly mix 10 parts oil with 1 part hardener and apply immediately. Pot life: 2–3 hours. Do not use after this time. Do not return mixed material to the original container.

Floors

1. Stir or shake the oil thoroughly before and during application.
2. Apply evenly and generously using a short-pile oil/wax roller . Work in sections of 5–10 m² at a time. Work quickly and do not roll into areas that have already started to dry.
3. Allow the first coat to dry for at least 2–3 hours .
4. Smooth with a red Swedish lacquer sanding pad and vacuum thoroughly.
5. Apply the second coat across the direction of the first application evenly and generously.
6. For a matter finish, carefully polish the still-wet second coat - preferably with a white pad. Do not polish for too long, and do not work on areas that have already started to dry.

Coverage

• Two coats of approx. 60–80 ml/m²
• each Coverage per coat: approx.
• 13–17 m²/l Coverage per coat: Coverage for two coats:

6–8.5 m²/l

Consumption depends on the type of wood, sanding, and absorbency.

• Drying 1K: Dust-dry after approx.1 hour , can be recoated after approx.1 hour 2–3 hours Can be carefully walked on after 24 hours and fully cured after.
• 5–7 days 2K with H2O-Hardener: Dust-dry after approx.1 hour , can be recoated after approx.1 hour At 20 °C, can be carefully walked on after approx.1 hour 24 hours.

and fully cured after

3–5 days The times depend on the temperature and humidity. Treat gently until fully cured, protect from water, and do not clean with a damp cloth. Application conditions: The oil, wood, and room must be at a temperature of

+15 to +25 °C . Avoid direct sunlight and intense heat. Ensure good ventilation during application and drying.

Underfloor heating: Switch off in good time before application. Maintain the required floor temperature during application and drying. Only switch it back on gradually after sufficient drying.

Tool cleaning: Clean tools with cold water immediately after use. Dispose of cleaning residues properly. Do not clean unmixed hardener with water. OLI NATURA® H2O-Hardener Safety:

Oil-soaked pads and cloths are not prone to spontaneous combustion. When adding hardener, also observe the safety instructions for the . Further information: Before application, consult the Technical Data Sheet in the

How do you care for and clean floors treated with OLI NATURA® Scandic-Oil CLASSIC?

Oiled wood floors are easy to care for and easy to repair. The surface can be refreshed by re-oiling. Small scratches can usually be sanded locally and re-oiled - without having to treat the entire floor again.

Cleaning: Protect from water until fully cured and do not clean with a damp cloth. Vacuum or sweep regularly so that sand does not cause fine scratches. If needed, clean slightly damp, not wet with OLI NATURA® wood soap . Avoid aggressive or abrasive cleaners.

Everyday protection: Wipe up spilled liquids immediately and avoid standing moisture. Felt pads under furniture help prevent scratches.

Initial care and refreshing: After drying overnight , initial care with OLI NATURA® Refresher is possible. If the water repellency decreases later or the wood looks dry and dull, refresh the floor with it. Apply a thin coat to the clean, dry surface.

Repair: Lightly sand small scratches and worn areas locally, thoroughly remove dust, and re-oil with the same oil used for the initial treatment .

Not classified as hazardous according to the CLP Regulation. Keep out of reach of children. Contains isothiazolinones; may cause allergic reactions.
For further safety information, see the separately provided
Safety Data Sheet. For 2-component application, also observe the label and
Safety Data Sheet for OLI NATURA® H2O-Hardener.